Product Code Database
Solar sails (also known as lightsails, light sails, and photon sails) are a method of spacecraft propulsion using radiation pressure exerted by sunlight on large surfaces. A number of spaceflight missions to test solar propulsion and navigation have been proposed since the 1980s. The two spacecraft to successfully use the technology for propulsion were IKAROS, launched in 2010, and LightSail-2, launched in 2019.
A useful analogy to solar sailing may be a sailboat; the light exerting a force on the large surface is akin to a sail being blown by the wind. High-energy Laser propulsion could be used as an alternative light source to exert much greater force than would be possible using sunlight, a concept known as beam sailing. Solar sail craft offer the possibility of low-cost operations combined with high speeds (relative to ) and long operating lifetimes. Since they have few moving parts and use no propellant, they can potentially be used numerous times for the delivery of payloads.
Solar sails use a phenomenon that has a proven, measured effect on astrodynamics. Solar pressure affects all spacecraft, whether in interplanetary space or in orbit around a planet or small body. A typical spacecraft going to Mars, for example, will be displaced thousands of kilometers by solar pressure, so the effects must be accounted for in trajectory planning, which has been done since the time of the earliest interplanetary spacecraft of the 1960s. Solar pressure also affects the orientation of a spacecraft, a factor that must be included in spacecraft design.Georgevic, R. M. (1973) "The Solar Radiation Pressure Forces and Torques Model", The Journal of the Astronautical Sciences, Vol. 27, No. 1, Jan–Feb. First known publication describing how solar radiation pressure creates forces and torques that affect spacecraft.
The total force exerted on an solar sail, for example, is about at Earth's distance from the Sun, making it a low-thrust propulsion system, similar to spacecraft propelled by electric engines, but as it uses no propellant, that force is exerted almost constantly and the collective effect over time is great enough to be considered a potential manner of propelling spacecraft.
The theory of electromagnetic fields and radiation, first published by James Clerk Maxwell in 1861–1864, shows that light has momentum and thus can exert pressure on objects. Maxwell's equations provide the theoretical foundation for sailing with light pressure. So by 1864, the physics community and beyond knew sunlight carried momentum that would exert a pressure on objects.
Jules Verne, in From the Earth to the Moon,Jules Verne (1865) De la Terre à la Lune ( From the Earth to the Moon) published in 1865, wrote "there will some day appear velocities far greater than these of, of which light or electricity will probably be the mechanical agent ... we shall one day travel to the moon, the planets, and the stars."Chris Impey, Beyond: Our Future in Space, W. W. Norton & Company (2015) This is possibly the first published recognition that light could move ships through space.
Pyotr Lebedev was first to successfully demonstrate light pressure, which he did in 1899 with a torsional balance;P. Lebedev, 1901, "Untersuchungen über die Druckkräfte des Lichtes", Annalen der Physik, 1901 Ernest Nichols and Gordon Hull conducted a similar independent experiment in 1901 using a Nichols radiometer.
Svante Arrhenius predicted in 1908 the possibility of solar radiation pressure distributing life spores across interstellar distances, providing one means to explain the concept of panspermia. He was apparently the first scientist to state that light could move objects between stars.Svante Arrhenius (1908) Worlds in the Making
Konstantin Tsiolkovsky first proposed using the pressure of sunlight to propel spacecraft through space in 1921 and suggested "using tremendous mirrors of very thin sheets to utilize the pressure of sunlight to attain cosmic velocities".Urbanczyk, Mgr., "Solar Sails-A Realistic Propulsion for Space Craft", Translation Branch Redstone Scientific Information Center Research and Development Directorate U.S. Army Missile Command Redstone Arsenal, Alabama, 1965.
Friedrich Zander (Tsander) published a technical paper in 1925 that included technical analysis of solar sailing. Zander wrote of "applying small forces" using "light pressure or transmission of light energy to distances by means of very thin mirrors".Friedrich Zander's 1925 paper, "Problems of flight by jet propulsion: interplanetary flights", was translated by NASA. See NASA Technical Translation F-147 (1964), p. 230.
JBS Haldane speculated in 1927 about the invention of tubular spaceships that would take humanity to space and how "wings of metallic foil of a square kilometre or more in area are spread out to catch the Sun's radiation pressure".JBS Haldane, The Last Judgement, New York and London, Harper & Brothers, 1927.
J. D. Bernal wrote in 1929, "A form of space sailing might be developed which used the repulsive effect of the Sun's rays instead of wind. A space vessel spreading its large, metallic wings, acres in extent, to the full, might be blown to the limit of Neptune's orbit. Then, Gravity assist, it would tack, close-hauled, down the gravitational field, spreading full sail again as it rushed past the Sun."J. D. Bernal (1929) The World, the Flesh & the Devil: An Enquiry into the Future of the Three Enemies of the Rational Soul
Arthur C. Clarke wrote Sunjammer, a science fiction short story originally published in the March 1964 issue of Boys' Life Short Stories . Arthurcclarke.net, 2007-2011, retrieved June 22, 2011 depicting a yacht race between solar sail spacecraft.
Carl Sagan, in the 1970s, popularized the idea of sailing on light using a giant structure which would reflect photons in one direction, creating momentum. He brought up his ideas in college lectures, books, and television shows. He was fixated on quickly launching this spacecraft in time to perform a rendezvous with Halley's Comet. Unfortunately, the mission didn't take place in time and he would never live to finally see it through.
The first formal technology and design effort for a solar sail began in 1976 at Jet Propulsion Laboratory for a proposed mission to rendezvous with Halley's Comet.
Electric solar wind sails can adjust their electrostatic fields and sail attitudes.
All these designs maneuver, though the mechanisms are different.
Magnetic sails bend the path of the charged protons that are in the solar wind. By changing the sails' attitudes, and the size of the magnetic fields, they can change the amount and direction of the thrust.
where p is the momentum, E is the energy (of the photon or flux), and c is the speed of light. Specifically, the momentum of a photon depends on its wavelength
Solar radiation pressure can be related to the irradiance (solar constant) value of 1361 W/m2 at 1 AU (Earth-Sun distance), as revised in 2011:
An ideal sail is flat and has 100% specular reflection. An actual sail will have an overall efficiency of about 90%, about 8.17 μN/m2, due to curvature (billow), wrinkles, absorbance, re-radiation from front and back, non-specular effects, and other factors. The force on a sail and the actual acceleration of the craft vary by the inverse square of distance from the Sun (unless extremely close to the SunMcInnes, C. R. and Brown, J. C. (1989) Solar Sail Dynamics with an Extended Source of Radiation Pressure, International Astronautical Federation, IAF-89-350, October.), and by the square of the cosine of the angle between the sail force vector and the radial from the Sun, so
where R is distance from the Sun in AU. An actual square sail can be modelled as:
Note that the force and acceleration approach zero generally around θ = 60° rather than 90° as one might expect with an ideal sail.Wright, Appendix B.
If some of the energy is absorbed, the absorbed energy will heat the sail, which re-radiates that energy from the front and rear surfaces, depending on the emissivity of those two surfaces.
Solar wind, the flux of charged particles blown out from the Sun, exerts a nominal dynamic pressure of about 3 to 4 nPa, three orders of magnitude less than solar radiation pressure on a reflective sail.
A sail craft has a characteristic acceleration, ac, which it would experience at 1 AU when facing the Sun. Note this value accounts for both the incident and reflected momentums. Using the value from above of 9.08 μN per square metre of radiation pressure at 1 AU, ac is related to areal density by:
Assuming 90% efficiency, ac = 8.17 / σ mm/s2
The lightness number, λ, is the dimensionless ratio of maximum vehicle acceleration divided by the Sun's local gravity. Using the values at 1 AU:
The lightness number is also independent of distance from the Sun because both gravity and light pressure fall off as the inverse square of the distance from the Sun. Therefore, this number defines the types of orbit maneuvers that are possible for a given vessel.
The table presents some example values. Payloads are not included. The first two are from the detailed design effort at JPL in the 1970s. The third, the lattice sailer, might represent about the best possible performance level. The dimensions for square and lattice sails are edges. The dimension for heliogyro is blade tip to blade tip.
| Square sail | 5.27 | 1.56 | 0.26 | 0.820 |
| Heliogyro | 6.39 | 1.29 | 0.22 | 15 |
| Lattice sailer | 0.07 | 117 | 20 | 0.840 |
Holding a constant attitude requires that the ACS maintain a net torque of zero on the craft. The total force and torque on a sail, or set of sails, is not constant along a trajectory. The force changes with solar distance and sail angle, which changes the billow in the sail and deflects some elements of the supporting structure, resulting in changes in the sail force and torque.
Sail temperature also changes with solar distance and sail angle, which changes sail dimensions. The radiant heat from the sail changes the temperature of the supporting structure. Both factors affect total force and torque.
To hold the desired attitude the ACS must compensate for all of these changes.Wright, ibid., Ch 6 and Appendix B.
Sail operating temperatures are a function of solar distance, sail angle, reflectivity, and front and back emissivities. A sail can be used only where its temperature is kept within its material limits. Generally, a sail can be used rather close to the Sun, around 0.25 AU, or even closer if carefully designed for those conditions.
Solar sail craft can approach the Sun to deliver observation payloads or to take up station keeping orbits. They can operate at 0.25 AU or closer. They can reach high orbital inclinations, including polar.
Solar sails can travel to and from all of the inner planets. Trips to Mercury and Venus are for rendezvous and orbit entry for the payload. Trips to Mars could be either for rendezvous or swing-by with release of the payload for Aerobraking.
| 800 σ = 5 g/m2 w/o cargo | 2 |
| 5 | |
| 10 | |
| 2000 σ = 3 g/m2 w/o cargo | 20 |
| 40 | |
| 70 |
The minimum transfer time to Jupiter for ac of 1 mm/s2 with no departure velocity relative to Earth is 2 years when using an indirect transfer (solar swing-by). The arrival speed ( V∞) is close to 17 km/s. For Saturn, the minimum trip time is 3.3 years, with an arrival speed of nearly 19 km/s.
| + Minimum times to the outer planets ( ac = 1 mm/s2) | ||||
| Time, yr | 2.0 | 3.3 | 5.8 | 8.5 |
| Speed, km/s | 17 | 19 | 20 | 20 |
It has been proposed that an inflated sail, made of beryllium, that starts at 0.05 AU from the Sun would gain an initial acceleration of 36.4 m/s2, and reach a speed of 0.00264c (about 950 km/s) in less than a day. Such proximity to the Sun could prove to be impractical in the near term due to the structural degradation of beryllium at high temperatures, diffusion of hydrogen at high temperatures as well as an electrostatic gradient, generated by the ionization of beryllium from the solar wind, posing a burst risk. A revised perihelion of 0.1 AU would reduce the aforementioned temperature and solar flux exposure.
Such a sail would take "Two and a half years to reach the heliopause, six and a half years to reach the Sun’s inner gravitational focus, with arrival at the inner Oort Cloud in no more than thirty years." "Such a mission could perform useful astrophysical observations en route, explore gravitational focusing techniques, and image Oort Cloud objects while exploring particles and fields in that region that are of galactic rather than solar origin."
In his book The Case for Mars, Robert Zubrin points out that the reflected sunlight from a large statite, placed near the polar terminator of the planet Mars, could be focused on one of the Martian polar ice caps to significantly warm the planet's atmosphere. Such a statite could be made from asteroid material.
A group of satellites designed to act as sails has been proposed to measure Earth's Energy Imbalance which is the most fundamental measure of the planet's rate of global warming. On-board state-of-the-art would measure shifts in the pressure differential between incoming solar and outgoing thermal radiation on opposing sides of each satellite. Measurement accuracy has been projected to be better than that achievable with compact radiometry detectors.
In the science fiction novel Rocheworld, Forward described a light sail propelled by super lasers. As the starship neared its destination, the outer portion of the sail would detach. The outer sail would then refocus and reflect the lasers back onto a smaller, inner sail. This would provide braking thrust to stop the ship in the destination star system.
Both methods pose monumental engineering challenges. The lasers would have to operate for years continuously at gigawatt strength. Forward's solution to this requires enormous solar panel arrays to be built at or near the planet Mercury. A planet-sized mirror or Fresnel lens would need to be located at several dozen astronomical units from the Sun to keep the lasers focused on the sail. The giant braking sail would have to act as a precision mirror to focus the braking beam onto the inner "deceleration" sail.
A potentially easier approach would be to use a maser to drive a "solar sail" composed of a mesh of wires with the same spacing as the wavelength of the microwaves directed at the sail, since the manipulation of microwave radiation is somewhat easier than the manipulation of visible light. The hypothetical "Starwisp" interstellar probe designForward, Robert L., "Starwisp: An Ultralight Interstellar Probe,” J. Spacecraft and Rockets, Vol. 22, May–June 1985, pp. 345-350.Landis, Geoffrey A., "Microwave Pushed Interstellar Sail: Starwisp Revisited," paper AIAA-2000-3337, 36th Joint Propulsion Conference, Huntsville, Alabama, July 17–19, 2000. would use microwaves, rather than visible light, to push it. Masers spread out more rapidly than optical lasers owing to their longer wavelength, and so would not have as great an effective range.
Masers could also be used to power a painted solar sail, a conventional sail coated with a layer of chemicals designed to evaporate when struck by microwave radiation. The momentum generated by this evaporation could significantly increase the thrust generated by solar sails, as a form of lightweight ablative laser propulsion.
To further focus the energy on a distant solar sail, Forward proposed a lens designed as a large zone plate. This would be placed at a location between the laser or maser and the spacecraft.
Another more physically realistic approach would be to use the light from the Sun to accelerate the spacecraft."Solar Sail Starships:Clipper Ships of the Galaxy," chapter 6, Eugene F. Mallove and Gregory L. Matloff, The Starflight Handbook: A Pioneer's Guide to Interstellar Travel, pp. 89-106, John Wiley & Sons, 1989. The ship would first drop into an orbit making a close pass to the Sun, to maximize the solar energy input on the sail, then it would begin to accelerate away from the system using the light from the Sun. Acceleration will drop approximately as the inverse square of the distance from the Sun, and beyond some distance, the ship would no longer receive enough light to accelerate it significantly, but would maintain the final velocity attained. When nearing the target star, the ship could turn its sails toward it and begin to use the outward pressure of the destination star to decelerate. Rockets could augment the solar thrust.
Similar solar sailing launch and capture were suggested for directed panspermia to expand life in other solar systems. Velocities of 0.05% the speed of light could be obtained by solar sails carrying 10 kg payloads, using thin solar sail vehicles with effective areal densities of 0.1 g/m2 with thin sails of 0.1 micrometre thickness and sizes on the order of one square kilometer. Alternatively, swarms of 1 mm capsules could be launched on solar sails with radii of 42 cm, each carrying 10,000 capsules of a hundred million extremophile microorganisms to seed life in diverse target environments.
Theoretical studies suggest relativistic speeds if the solar sail harnesses a supernova.
Parachutes have very low mass, but a parachute is not a workable configuration for a solar sail. Analysis shows that a parachute configuration would collapse from the forces exerted by shroud lines, since radiation pressure does not behave like aerodynamic pressure, and would not act to keep the parachute open.Wright, ibid., p. 71, last paragraph
The highest thrust-to-mass designs for ground-assembled deploy-able structures are square sails with the masts and guy lines on the dark side of the sail. Usually there are four masts that spread the corners of the sail, and a mast in the center to hold . One of the largest advantages is that there are no hot spots in the rigging from wrinkling or bagging, and the sail protects the structure from the Sun. This form can, therefore, go close to the Sun for maximum thrust. Most designs steer with small moving sails on the ends of the spars.
In the 1970s JPL studied many rotating blade and ring sails for a mission to rendezvous with Halley's Comet. The intention was to stiffen the structures using angular momentum, eliminating the need for struts, and saving mass. In all cases, surprisingly large amounts of tensile strength were needed to cope with dynamic loads. Weaker sails would ripple or oscillate when the sail's attitude changed, and the oscillations would add and cause structural failure. The difference in the thrust-to-mass ratio between practical designs was almost nil, and the static designs were easier to control.
JPL's reference design was called the "heliogyro". It had plastic-film blades deployed from rollers and held out by centrifugal forces as it rotated. The spacecraft's attitude and direction were to be completely controlled by changing the angle of the blades in various ways, similar to the cyclic and collective pitch of a helicopter. Although the design had no mass advantage over a square sail, it remained attractive because the method of deploying the sail was simpler than a strut-based design. The CubeSail (UltraSail) is an active project aiming to deploy a heliogyro sail.
Heliogyro design is similar to the blades on a helicopter. The design is faster to manufacture due to lightweight centrifugal stiffening of sails. Also, they are highly efficient in cost and velocity because the blades are lightweight and long. Unlike the square and spinning disk designs, heliogyro is easier to deploy because the blades are compacted on a reel. The blades roll out when they are deploying after the ejection from the spacecraft. As the heliogyro travels through space the system spins around because of the centrifugal acceleration. Finally, payloads for the space flights are placed in the center of gravity to even out the distribution of weight to ensure stable flight.
JPL also investigated "ring sails" (Spinning Disk Sail in the above diagram), panels attached to the edge of a rotating spacecraft. The panels would have slight gaps, about one to five percent of the total area. Lines would connect the edge of one sail to the other. Masses in the middles of these lines would pull the sails taut against the coning caused by the radiation pressure. JPL researchers said that this might be an attractive sail design for large crewed structures. The inner ring, in particular, might be made to have artificial gravity roughly equal to the gravity on the surface of Mars.
A solar sail can serve a dual function as a high-gain antenna. Designs differ, but most modify the metallizing pattern to create a holographic monochromatic lens or mirror in the radio frequencies of interest, including visible light.
Eric Drexler developed a concept for a sail in which the polymer was removed. He proposed very high thrust-to-mass solar sails, and made prototypes of the sail material. His sail would use panels of thin aluminium film (30 to 100 thick) supported by a tensile structure. The sail would rotate and would have to be continually under thrust. He made and handled samples of the film in the laboratory, but the material was too delicate to survive folding, launch, and deployment. The design planned to rely on space-based production of the film panels, joining them to a deployable tension structure. Sails in this class would offer high area per unit mass and hence accelerations up to "fifty times higher" than designs based on deploy-able plastic films.
The material developed for the Drexler solar sail was a thin aluminium film with a baseline thickness of 0.1 μm, to be fabricated by vapor deposition in a space-based system. Drexler used a similar process to prepare films on the ground. As anticipated, these films demonstrated adequate strength and robustness for handling in the laboratory and for use in space, but not for folding, launch, and deployment.
Research by Geoffrey Landis in 1998–1999, funded by the NASA Institute for Advanced Concepts, showed that various materials such as alumina for laser lightsails and carbon fiber for microwave pushed lightsails were superior sail materials to the previously standard aluminium or Kapton films.
In 2000, Energy Science Laboratories developed a new carbon fiber material that might be useful for solar sails. The material is over 200 times thicker than conventional solar sail designs, but it is so porous that it has the same mass. The rigidity and durability of this material could make solar sails that are significantly sturdier than plastic films. The material could self-deploy and should withstand higher temperatures.
There has been some theoretical speculation about using molecular manufacturing techniques to create advanced, strong, hyper-light sail material, based on Carbon nanotube mesh weaves, where the weave "spaces" are less than half the wavelength of light impinging on the sail. While such materials have so far only been produced in laboratory conditions, and the means for manufacturing such material on an industrial scale are not yet available, such materials could mass less than 0.1 g/m2, making them lighter than any current sail material by a factor of at least 30. For comparison, 5 micrometre thick Mylar sail material mass 7 g/m2, aluminized Kapton films have a mass as much as 12 g/m2, and Energy Science Laboratories' new carbon fiber material masses 3 g/m2.
The least dense metal is lithium, about 5 times less dense than aluminium. Fresh, unoxidized surfaces are reflective. At a thickness of 20 nm, lithium has an area density of 0.011 g/m2. A high-performance sail could be made of lithium alone at 20 nm (no emission layer). It would have to be fabricated in space and not used to approach the Sun. In the limit, a sail craft might be constructed with a total areal density of around 0.02 g/m2, giving it a lightness number of 67 and ac of about 400 mm/s2. Magnesium and beryllium are also potential materials for high-performance sails. These 3 metals can be alloyed with each other and with aluminium.
In the future, fabrication could take place in orbit inside large frames that support the sail. This would result in lower mass sails and elimination of the risk of deployment failure.
In orbits around planets or other bodies, the sail is oriented so that its force vector has a component along the velocity vector, either in the direction of motion for an outward spiral, or against the direction of motion for an inward spiral.
Trajectory optimizations can often require intervals of reduced or zero thrust. This can be achieved by rolling the craft around the Sun line with the sail set at an appropriate angle to reduce or remove the thrust.
A lunar swing-by can have important benefits for trajectories leaving from or arriving at Earth. This can reduce trip times, especially in cases where the sail is heavily loaded. A swing-by can also be used to obtain favorable departure or arrival directions relative to Earth.
A planetary swing-by could also be employed similar to what is done with coasting spacecraft, but good alignments might not exist due to the requirements for overall optimization of the trajectory.Wright, ibid., Ch 6 and Appendix C.
Hayabusa also used solar pressure on its solar paddles as a method of attitude control to compensate for broken and chemical thruster.
MTSAT-1R (Multi-Functional Transport Satellite)'s solar sail counteracts the torque produced by sunlight pressure on the solar array. The trim tab on the solar array makes small adjustments to the torque balance.
In 1999, a full-scale deployment of a solar sail was tested on the ground at DLR/ESA in Cologne.
A 15-meter-diameter solar sail (SSP, solar sail sub payload, soraseiru sabupeiro-do) was launched together with ASTRO-F on a M-V rocket on February 21, 2006, and made it to orbit. It deployed from the stage, but opened incompletely.
On August 9, 2004, the Japanese ISAS successfully deployed two prototype solar sails from a sounding rocket. A clover-shaped sail was deployed at 122 km altitude and a fan-shaped sail was deployed at 169 km altitude. Both sails used 7.5-micrometre film. The experiment purely tested the deployment mechanisms, not propulsion.
JAXA successfully tested IKAROS in 2010. The goal was to deploy and control the sail and, for the first time, to determine the minute orbit perturbations caused by light pressure. Orbit determination was done by the nearby AKATSUKI probe from which IKAROS detached after both had been brought into a transfer orbit to Venus. The total effect over the six month flight was 100 m/s.
Until 2010, no solar sails had been successfully used in space as primary propulsion systems. On 21 May 2010, the Japan Aerospace Exploration Agency (JAXA) launched the IKAROS spacecraft, which deployed a 200 m2 polyimide experimental solar sail on June 10. In July, the next phase for the demonstration of acceleration by radiation began. On 9 July 2010, it was verified that IKAROS collected radiation from the Sun and began photon acceleration by the orbit determination of IKAROS by range-and-range-rate (RARR) that is newly calculated in addition to the data of the relativization accelerating speed of IKAROS between IKAROS and the Earth that has been taken since before the Doppler effect was utilized. The data showed that IKAROS appears to have been solar-sailing since 3 June when it deployed the sail.
IKAROS has a diagonal spinning square sail 14×14 m (196 m2) made of a thick sheet of polyimide. The polyimide sheet had a mass of about 10 grams per square metre. A thin-film solar array is embedded in the sail. Eight LCD panels are embedded in the sail, whose reflectance can be adjusted for attitude control. IKAROS spent six months traveling to Venus, and then began a three-year journey to the far side of the Sun.
NASA launched the second NanoSail-D unit stowed inside the FASTSAT satellite on the Minotaur IV on November 19, 2010. The ejection date from the FASTSAT microsatellite was planned for December 6, 2010, but deployment only occurred on January 20, 2011.
On Carl Sagan's 75th birthday (November 9, 2009) the Planetary Society announced plans to make three further attempts, dubbed LightSail-1, -2, and -3. The new design will use a 32 m2 Mylar sail, deployed in four triangular segments like NanoSail-D. The launch configuration is a 3U CubeSat format, and as of 2015, it was scheduled as a secondary payload for a 2016 launch on the first SpaceX Falcon Heavy launch.
"LightSail-1" was launched on 20 May 2015. The purpose of the test was to allow a full checkout of the satellite's systems in advance of LightSail-2. Its deployment orbit was not high enough to escape Earth's atmospheric drag and demonstrate true solar sailing.
"LightSail-2" was launched on 25 June 2019, and deployed into a much higher low Earth orbit. Its solar sails were deployed on 23 July 2019. It reentered the atmosphere on 17 November 2022. LightSail-2 successfully demonstrated propulsion by solar sail.
ACS3 consists of a 12U (unit)1 unit=10cm × 10cm × 11.35cm (3.94in × 3.94in × 4.47in) − CubeSat small satellite (23 cm x 23 cm x 34 cm; 16 kg) that unfolds a quadratic solar sail consisting of a polyethylene naphthalate film coated on one side with Aluminium for reflectivity and on the other side with chromium to increase thermal emissivity. The sail is held by a novel unfolding system of four long carbon fiber reinforced polymer booms that roll-up for storage.
ACS3 was launched on 23 April 2024 on the Electron "Beginning Of The Swarm" mission. The ACS3 successfully made contact with ground stations following deployment in early May. The solar sail was confirmed as successfully operational by mission operators on 29 August 2024.
On 25 October 2024 it was reported "... a bent support arm has made it (ACS3) lose direction and spin out of control in space."
Jack Vance wrote a short story about a training mission on a solar-sail-powered spaceship in "Sail 25", published in 1961.
Arthur C. Clarke and Poul Anderson (writing as Winston P. Sanders) independently published stories featuring solar sails, both stories titled "Sunjammer," in 1964. Clarke retitled his story "The Wind from the Sun" when it was reprinted, in order to avoid confusion. Sunjammer, ISFDB.
In Larry Niven and Jerry Pournelle's 1974 novel The Mote in God's Eye, aliens are discovered when their laser-sail propelled probe enters human space.
A similar technology was the theme in the episode "". In the episode, Lightships are described as an ancient technology used by to travel beyond their solar system by using light from the Bajoran sun and specially constructed sails to propel them through space ().
In the 2002 Star Wars film Attack of the Clones, the main villain Count Dooku was seen using a spacecraft with solar sails.
In the 2009 film Avatar, the spacecraft which transports the protagonist Jake Sully to the Alpha Centauri system, the ISV Venture Star, uses solar sails as a means of propulsion to accelerate the vehicle away from the Earth towards Alpha Centauri.
In the third season of Apple TV+'s alternate history TV show For All Mankind, the fictional NASA spaceship Sojourner 1 utilises solar sails for additional propulsion on its way to Mars.
In the 2022 show Pantheon, a solar sail is used to send the SafeSurf program to Alpha Centauri.
In the final episode of the first season of 2024 Netflix TV show, 3 Body Problem, one of the protagonists, Will Downing, has his Cryonics frozen brain launched into space toward the oncoming Trisolarian spaceship, using solar sails and nuclear pulse propulsion to accelerate it to a fraction of the speed of light.
Satellites
Robert L. Forward has commented that a solar sail could be used to modify the orbit of a satellite about the Earth. In the limit, a sail could be used to "hover" a satellite above one pole of the Earth. Spacecraft fitted with solar sails could also be placed in close orbits such that they are stationary with respect to either the Sun or the Earth, a type of satellite named by Forward a "statite". This is possible because the propulsion provided by the sail offsets the gravitational attraction of the Sun. Such an orbit could be useful for studying the properties of the Sun for long durations. Likewise a solar sail-equipped spacecraft could also remain on station nearly above the polar solar terminator of a planet such as the Earth by tilting the sail at the appropriate angle needed to counteract the planet's gravity.
Trajectory corrections
The MESSENGER probe orbiting Mercury used light pressure on its solar panels to perform fine trajectory corrections on the way to Mercury. By changing the angle of the solar panels relative to the Sun, the amount of solar radiation pressure was varied to adjust the spacecraft trajectory more delicately than possible with thrusters. Minor errors are greatly amplified by gravity assist maneuvers, so using radiation pressure to make very small corrections saved large amounts of propellant.
Interstellar flight
In the 1970s, Robert Forward proposed two beam-powered propulsion schemes using either lasers or to push giant sails to a significant fraction of the speed of light.
Deorbiting artificial satellites
Small solar sails have been proposed to accelerate the deorbiting of small artificial satellites from Earth orbits. Satellites in low Earth orbit can use a combination of solar pressure on the sail and increased atmospheric drag to accelerate satellite reentry. A de-orbit sail developed at Cranfield University is part of the UK satellite TechDemoSat-1, launched in 2014. The sail deployed at the end of the satellite's five-year useful life in May 2019. The sail's purpose is to bring the satellite out of orbit over a period of about 25 years. "22,295,864 amazing things you need to know about the UK’s newest satellite" . Innovate UK. In July 2015 British 3U CubeSat called DeorbitSail was launched into space with the purpose of testing 16 m2 deorbit structure, but eventually it failed to deploy it. A student 2U CubeSat mission called PW-Sat2, launched in December 2018 and tested a 4 m2 deorbit sail. It successfully deorbited in February 2021. In June 2017, a second British 3U CubeSat called InflateSail deployed a 10 m2 deorbit sail at an altitude of .
In June 2017 the 3U Cubesat URSAMAIOR has been launched in low Earth orbit to test the deorbiting system ARTICA developed by Spacemind. The device, which occupies only 0.4 U of the cubesat, shall deploy a sail of 2.1 m2 to deorbit the satellite at the end of the operational life.
Sail configurations
IKAROS, launched in 2010, was the first practical solar sail vehicle. As of 2015, it was still under thrust, proving the practicality of a solar sail for long-duration missions. It is spin-deployed, with tip-masses in the corners of its square sail. The sail is made of thin polyimide film, coated with evaporated aluminium. It steers with electrically controlled liquid crystal panels. The sail slowly spins, and these panels turn on and off to control the attitude of the vehicle. When on, they diffuse light, reducing the momentum transfer to that part of the sail. When off, the sail reflects more light, transferring more momentum. In that way, they turn the sail. Thin-film are also integrated into the sail, powering the spacecraft. The design is very reliable, because spin deployment, which is preferable for large sails, simplified the mechanisms to unfold the sail and the LCD panels have no moving parts.
Reflective sail making
Materials
The most common material in current designs is a thin layer of aluminum coating on a polymer (plastic) sheet, such as aluminized 2 μm Kapton film. The polymer provides mechanical support as well as flexibility, while the thin metal layer provides the reflectivity. Such material resists the heat of a pass close to the Sun and still remains reasonably strong. The aluminum reflecting film is on the Sun side. The sails of Cosmos 1 were made of aluminized PET film (Mylar).
Reflection and emissivity layers
Aluminium is the common choice for the reflection layer. It typically has a thickness of at least 20 nm, with a reflectivity of 0.88 to 0.90. Chromium is a good choice for the emission layer on the face away from the Sun. It can readily provide emissivity values of 0.63 to 0.73 for thicknesses from 5 to 20 nm on plastic film. Usable emissivity values are empirical because thin-film effects dominate; bulk emissivity values do not hold up in these cases because material thickness is much thinner than the emitted wavelengths.Wright, ibid. Ch 4
Fabrication
Sails are fabricated on Earth on long tables where ribbons are unrolled and joined to create the sails. Sail material needed to have as little weight as possible because it would require the use of the shuttle to carry the craft into orbit. Thus, these sails are packed, launched, and unfurled in space.Rowe, W. m. 'Sail film materials and supporting structure for a solar sail, a preliminary design, volume 4." Jet Propulsion Lab. California, Pasadena, California.
Operations
Changing orbits
Sailing operations are simplest in interplanetary orbits, where altitude changes are done at low rates. For outward bound trajectories, the sail force vector is oriented forward of the Sun line, which increases orbital energy and angular momentum, resulting in the craft moving farther from the Sun. For inward trajectories, the sail force vector is oriented behind the Sun line, which decreases orbital energy and angular momentum, resulting in the craft moving in toward the Sun. It is worth noting that only the Sun's gravity pulls the craft toward the Sun—there is no analog to a sailboat's tacking to windward. To change orbital inclination, the force vector is turned out of the plane of the velocity vector.
Swing-by maneuvers
A close solar passage can be used to increase a craft's energy. The increased radiation pressure combines with the efficacy of being deep in the Sun's gravity well to substantially increase the energy for runs to the outer Solar System. The optimal approach to the Sun is done by increasing the orbital eccentricity while keeping the energy level as high as practical. The minimum approach distance is a function of sail angle, thermal properties of the sail and other structure, load effects on structure, and sail optical characteristics (reflectivity and emissivity). A close passage can result in substantial optical degradation. Required turn rates can increase substantially for a close passage. A sail craft arriving at a star can use a close passage to reduce energy, which also applies to a sail craft on a return trip from the outer Solar System.
Laser powered
The following table lists some example concepts using beamed laser propulsion as proposed by the physicist Robert L. Forward:
1. Flyby – Alpha Centauri, 40 years 11% @ 0.17 ly 2. Rendezvous – Alpha Centauri, 41 years 21% @ 4.29 ly 21% @ 4.29 ly 3. Crewed – Epsilon Eridani, 51 years (including 5 years exploring star system) 50% @ 0.4 ly 50% @ 10.4 ly 50% @ 10.4 ly 50% @ 0.4 ly
Interstellar travel catalog to use photogravitational assists for a full stop
24.20 1.52 0.50 6.94 50.05 10.70 16.67 14.66 49.85 0.50
Projects operating or completed
Attitude (orientation) control
Both the Mariner 10 mission, which flew by the planets Mercury and Venus, and the MESSENGER mission to Mercury demonstrated the use of solar pressure as a method of attitude control in order to conserve attitude-control propellant.
Ground deployment tests
NASA has successfully tested deployment technologies on small scale sails in vacuum chambers.
Suborbital tests
Cosmos 1, a joint private project between Planetary Society, Cosmos Studios and Russian Academy of Science attempted to launch a suborbital prototype vehicle in 2005, which was destroyed due to a rocket failure.
Znamya 2
On February 4, 1993, the Znamya 2, a 20-meter wide aluminized-mylar reflector, was successfully deployed from the Russian Mir space station. It was the first thin film reflector of such type successfully deployed in space using the mechanism based on centrifugal force.Tim Folger, «New moon — Russian satellite acts as a mirror to light remote areas» Discover, Jan, 1994 ( web version , (accessed 2008 August 29)). Although the deployment succeeded, propulsion was not demonstrated. A second test in 1999, Znamya 2.5, failed to deploy properly.
IKAROS 2010
On 21 May 2010, Japan Aerospace Exploration Agency (JAXA) launched the world's first interplanetary solar sail spacecraft "IKAROS" (Interplanetary Kite-craft Accelerated by Radiation Of the Sun) to Venus. Using a new solar-photon propulsion method, it was the first true solar sail spacecraft fully propelled by sunlight, Maiden voyage for first true space sail, New Scientist and was the first spacecraft to succeed in solar sail flight.
NanoSail-D 2010
A team from the NASA Marshall Space Flight Center (Marshall), along with a team from the NASA Ames Research Center, developed a solar sail mission called NanoSail-D, which was lost in a launch failure aboard a Falcon 1 rocket on 3 August 2008. The second backup version, NanoSail-D2, also sometimes called simply NanoSail-D, was launched with FASTSAT on a Minotaur IV on November 19, 2010, becoming NASA's first solar sail deployed in low earth orbit. The objectives of the mission were to test sail deployment technologies, and to gather data about the use of solar sails as a simple, "passive" means of de-orbiting dead satellites and space debris. The NanoSail-D structure was made of aluminium and plastic, with the spacecraft massing less than . The sail has about of light-catching surface. After some initial problems with deployment, the solar sail was deployed and over the course of its 240-day mission reportedly produced a "wealth of data" concerning the use of solar sails as passive deorbit devices.
Planetary Society LightSail Projects
On June 21, 2005, a joint private project between Planetary Society, Cosmos Studios and Russian Academy of Science launched a prototype sail Cosmos 1 from a submarine in the Barents Sea, but the Volna rocket failed, and the spacecraft failed to reach orbit. They intended to use the sail to gradually raise the spacecraft to a higher Earth orbit over a mission duration of one month. The launch attempt sparked public interest according to Louis Friedman. Despite the failed launch attempt of Cosmos 1, The Planetary Society received applause for their efforts from the space community and sparked a rekindled interest in solar sail technology.
NEA Scout
The Near-Earth Asteroid Scout (NEA Scout) was a mission jointly developed by NASA's Marshall Space Flight Center (MSFC) and the Jet Propulsion Laboratory (JPL), consisting of a controllable low-cost CubeSat solar sail spacecraft capable of encountering near-Earth asteroids (NEA). Four booms were to deploy, unfurling the aluminized polyimide solar sail. In 2015, NASA announced it had selected NEA Scout to launch as one of several secondary payloads aboard Artemis 1, the first flight of the agency's heavy-lift SLS launch vehicle. However, the craft was considered lost with the failure to establish communications shortly after launch in 2022.
Advanced Composite Solar Sail System (ACS3)
The NASA Advanced Composite Solar Sail System (ACS3) is a technology demonstration of solar sail technology for future small spacecraft. It was selected in 2019 by NASA's CubeSat Launch Initiative (CSLI) to be launched as part of the ELaNa program.
Projects proposed or cancelled or not selected
Despite the losses of Cosmos 1 and NanoSail-D (about 23cm x 23cm x 34cm) which were due to failure of their launchers, scientists and engineers around the world remain encouraged and continue to work on solar sails. While most direct applications created so far intend to use the sails as inexpensive modes of cargo transport, some scientists are investigating the possibility of using solar sails as a means of transporting humans. This goal is strongly related to the management of very large (i.e. well above 1 km2) surfaces in space and the sail making advancements. Development of solar sails for crewed space flight is still in its infancy.
Sunjammer 2015
A technology demonstration sail craft, dubbed Sunjammer, was in development with the intent to prove the viability and value of sailing technology. Sunjammer had a square sail, wide on each side, giving it an effective area of . It would have traveled from the Sun-Earth Lagrangian point from Earth to a distance of . The demonstration was expected to launch on a Falcon 9 in January 2015. It would have been a secondary payload, released after the placement of the DSCOVR climate satellite at the L1 point. Citing a lack of confidence in the ability of its contractor LGarde to deliver, the mission was cancelled by NASA in October 2014.
OKEANOS
OKEANOS (Outsized Kite-craft for Exploration and Astronautics in the Outer Solar System) was a proposed mission concept by Japan's JAXA to Jupiter's Jupiter Trojan using a hybrid solar sail for propulsion; the sail would have been covered with thin solar panels to power an ion engine. In-situ analysis of the collected samples would have been performed by either direct contact or using a lander carrying a high-resolution mass spectrometer. A lander and a sample-return to Earth were options under study. Sampling Scenario for the Trojan Asteroid Exploration Mission (PDF). Jun Matsumoto, Jun Aoki, Yuske Oki, Hajime Yano. 2015. The OKEANOS Jupiter Trojan Asteroid Explorer was a finalist for Japan's ISAS 2nd Large-class mission to be launched in the late 2020s. However, it was not selected.
Solar Cruiser
In August 2019, NASA awarded the Solar Cruiser team $400,000 for nine-month mission concept studies. The spacecraft would have a solar sail and would orbit the Sun in a polar orbit, while the coronagraph instrument would enable simultaneous measurements of the Sun's magnetic field structure and velocity of coronal mass ejections. NASA Selects Proposals to Demonstrate SmallSat Technologies to Study Interplanetary Space. NASA press release, 15 August 2019. If selected for further development, it would have launched in 2025. However, Solar Cruiser was not approved to advance to phase C of its development cycle and was subsequently discontinued.
Projects still in development or unknown status
Gossamer deorbit sail
, the European Space Agency (ESA) has a proposed deorbit sail, named " Gossamer", that would be intended to be used to accelerate the deorbiting of small (less than ) artificial satellites from low Earth orbits. The launch mass is with a launch volume of only . Once deployed, the sail would expand to and would use a combination of solar pressure on the sail and increased atmospheric drag to accelerate satellite reentry.
Breakthrough Starshot
The well-funded Breakthrough Starshot project announced on April 12, 2016, aims to develop a fleet of 1000 light sail nanocraft carrying miniature cameras, propelled by ground-based lasers and send them to Alpha Centauri at 20% the speed of light. Starshot - Concept. The trip would take 20 years.
In popular culture
Cordwainer Smith gives a description of solar-sail-powered spaceships in "The Lady Who Sailed The Soul", published first in April 1960.
See also
Bibliography
(Kindle-edition), ASIN: B00A9YGY4I
External links
target="_blank" rel="nofollow"> "NASA to Attempt Historic Solar Sail Deployment", NASA, June 28, 2008
|
|
